Vehicles
Sections
33 not categorized PORSCHE 356 A SHEET METACan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) N90048801 Known as: speed nut / speed nut b 3,5 View/Change Diagram
From $1.00
Make a selection FVD504911RSR These fender flares are made of metal sheet set (4pcs): - fender flare front left - fender flare front right - fender flare rear left - fender flare rear right
$5,402.10
Make a selection 150752 As we all know the only way to install the optional oil pressure gauge is to replace the oil pressure switch with the much "fatter" oil pressure sender. this cannot be accomplished without cutting the sheet metal or extending the hole out of the sheet metal and attaching the sending unit. this hose will give you the needed length. (might need to grind down the male end for a proper fit) General Fitment914 1970-76
$38.00
Make a selection N0139542 Known as: oval-head sheetmetal screw b2,9 x 13 / oval-head sheetmetal screw / oval-head sheetmetal screw b 2,9 x 13 View/Change Diagram
From $1.55
Make a selection SIC50111702 This section of sheet metal can be found in the front trunk, in front of the visible section of fuel tank, connecting all the way across the chassis to the leading edge of the battery box. Comes to you ready to be welded in without requiring fabrication work. Rid your car of rust using trusted sheet metal components.
$149.03
Make a selection FVD53191100 If a door check has separated or ripped out, this repair kit with stainless steel sheets can prevent further tearing or damage. For assembly, it is sufficient to adhere these plates to the sheet metal and secure with a 2-component adhesive and then screw it in. Please note: for some doors, the outer panel must be adjusted. This kit has its limits as it depends on the size of the area that is damaged.
$28.60
Make a selection 91450411110 This is the black protective edging that fits on the edge of the engine sheet metal. It finishes the raw edge to prevent cuts. It also fits on the bottom of the engine lid. You will need two rolls in order to finish the sides of the engine lid. View/Change Diagram
From $16.90
Make a selection 91150403100GRV3 This is a sheet metal repair cup that is located behind the fuel door. It includes the fuel door hinge mount, lock (part # 901 504 034 20grv), buffer (part # 911 025 679 00) and tube for the pull cable. It is manufactured by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment ...(choose a part on the right to read more)
$284.90
Make a selection 99951300740 For the rear 914 harness where it is tied to the rear sheetmetal View/Change Diagram
$2.50
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection 021119543A This is the black protective edging that fits on the edge of the engine sheetmetal. it finishes the raw edge to prevent cuts. View/Change Diagram
$25.43
Make a selection AAA25600A This kit consists of all the proper hardware to install heat exchangers and a muffler, including the rare copper locking nuts to ensure a perfect installation. Remember to install the exchangers one at a time and torque in an x pattern to 18 ft lbs. General Fitment914 1970-76
$66.40
Make a selection 90014306602 Known as: oval-head sheet metal screw View/Change Diagram
$1.25
Make a selection N0141412 Known as: oval-head sheetmetal screw View/Change Diagram
$1.25
Make a selection
$1.10
Make a selection F916 Our five piece set of 914-6 sheet metal exactly duplicates the real thing as well as providing the unavailable right rear section. When installed, it enables your six cylinder engine to perfectly fit the engine bay. Painted in black.
$437.25
Make a selection SICG50196500 This section of sheet metal surrounds the torsion tube on the left side of the car. Comes to you ready to be welded in without requiring fabrication work. Rid your car of rust using trusted sheetmetal components. Fits all 911 and 912 models built between 1965 and 1989.
$39.07
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |